<br><br><div class="gmail_quote">On Mon, Feb 4, 2013 at 4:56 AM, <span dir="ltr"><<a href="mailto:jep200404@columbus.rr.com" target="_blank">jep200404@columbus.rr.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
On Sun, 3 Feb 2013 22:28:25 -0600, Thomas Cranston <<a href="mailto:thomas.w.cranston@gmail.com">thomas.w.cranston@gmail.com</a>> wrote:<br>
<br>
> knoppix 5.1.1<br>
<br>
That's a remarkably old version of Knoppix, much older than your drive.<br>
Maybe that old version of Knoppix does not have information<br>
about your new drive.<br>
<br>
So, use a new version of Knoppix.<br>
Alternatively, you could try to update the version of<br>
smartmontools, although you probably don't have enough<br>
RAM or patience for it.<br>
<div class="im"><br>
> I shutdown, removed Knoppix live disk and booted to hdd with Ubuntu<br>
> 10.04, I then ran smartctl:<br>
<br>
</div><div class="im">> Device is: Not in smartctl database [for details use: -P showall]<br>
<br>
</div>Use a new version of Ubuntu as live disk.<br>
<br>
I booted live Mint 14 and ran smartctl on new hdd. Did not want a project inside of a project.</blockquote><div><br>mint@mint ~ $ sudo smartctl -a /dev/sda<br>smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-17-generic] (local build)<br>
Copyright (C) 2002-12 by Bruce Allen, <a href="http://smartmontools.sourceforge.net">http://smartmontools.sourceforge.net</a><br><br>=== START OF INFORMATION SECTION ===<br>Device Model: ST9750420AS<br>Serial Number: 6WS2VNV8<br>
LU WWN Device Id: 5 000c50 05b0e28ed<br>Firmware Version: 0001SDM5<br>User Capacity: 750,156,374,016 bytes [750 GB]<br>Sector Sizes: 512 bytes logical, 4096 bytes physical<br>Device is: Not in smartctl database [for details use: -P showall]<br>
ATA Version is: 8<br>ATA Standard is: ATA-8-ACS revision 4<br>Local Time is: Mon Feb 4 18:30:09 2013 UTC<br>SMART support is: Available - device has SMART capability.<br>SMART support is: Enabled<br><br>=== START OF READ SMART DATA SECTION ===<br>
SMART overall-health self-assessment test result: PASSED<br><br>General SMART Values:<br>Offline data collection status: (0x82) Offline data collection activity<br> was completed without error.<br> Auto Offline Data Collection: Enabled.<br>
Self-test execution status: ( 0) The previous self-test routine completed<br> without error or no self-test has ever <br> been run.<br>Total time to complete Offline <br>data collection: ( 0) seconds.<br>
Offline data collection<br>capabilities: (0x7b) SMART execute Offline immediate.<br> Auto Offline data collection on/off support.<br> Suspend Offline collection upon new<br>
command.<br> Offline surface scan supported.<br> Self-test supported.<br> Conveyance Self-test supported.<br> Selective Self-test supported.<br>
SMART capabilities: (0x0003) Saves SMART data before entering<br> power-saving mode.<br> Supports SMART auto save timer.<br>Error logging capability: (0x01) Error logging supported.<br>
General Purpose Logging supported.<br>Short self-test routine <br>recommended polling time: ( 2) minutes.<br>Extended self-test routine<br>recommended polling time: ( 141) minutes.<br>Conveyance self-test routine<br>
recommended polling time: ( 3) minutes.<br>SCT capabilities: (0x303f) SCT Status supported.<br> SCT Error Recovery Control supported.<br> SCT Feature Control supported.<br>
SCT Data Table supported.<br><br>SMART Attributes Data Structure revision number: 10<br>Vendor Specific SMART Attributes with Thresholds:<br>ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE<br>
1 Raw_Read_Error_Rate 0x000f 100 100 006 Pre-fail Always - 70488<br> 3 Spin_Up_Time 0x0003 098 098 085 Pre-fail Always - 0<br> 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 14<br>
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0<br> 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 32<br> 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 1<br>
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0<br> 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 7<br>184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0<br>
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0<br>188 Command_Timeout 0x0032 100 253 000 Old_age Always - 0<br>189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0<br>
190 Airflow_Temperature_Cel 0x0022 064 060 045 Old_age Always - 36 (Min/Max 26/36)<br>191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0<br>192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0<br>
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 26<br>194 Temperature_Celsius 0x0022 036 040 000 Old_age Always - 36 (0 26 0 0 0)<br>195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 70488<br>
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0<br>198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0<br>199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0<br>
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 118154550312961<br>241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 0<br>242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 10805<br>
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0<br><br>SMART Error Log Version: 1<br>No Errors Logged<br><br>SMART Self-test log structure revision number 1<br>No self-tests have been logged. [To run self-tests, use: smartctl -t]<br>
<br><br>SMART Selective self-test log data structure revision number 1<br> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS<br> 1 0 0 Not_testing<br> 2 0 0 Not_testing<br> 3 0 0 Not_testing<br>
4 0 0 Not_testing<br> 5 0 0 Not_testing<br>Selective self-test flags (0x0):<br> After scanning selected spans, do NOT read-scan remainder of disk.<br>If Selective self-test is pending on power-up, resume after 0 minute delay.<br>
<br>mint@mint ~ $<br><br>The above results came up instantly. Do not think it checked the entire disk for bad sectors.<br><br>Will read man about -t and -T options to run longer tests.<br><br>Tom<br> </div></div><br>