[colug-432] smartctl, Knoppix
Thomas Cranston
thomas.w.cranston at gmail.com
Mon Feb 4 14:45:50 EST 2013
On Mon, Feb 4, 2013 at 4:56 AM, <jep200404 at columbus.rr.com> wrote:
> On Sun, 3 Feb 2013 22:28:25 -0600, Thomas Cranston <
> thomas.w.cranston at gmail.com> wrote:
>
> > knoppix 5.1.1
>
> That's a remarkably old version of Knoppix, much older than your drive.
> Maybe that old version of Knoppix does not have information
> about your new drive.
>
> So, use a new version of Knoppix.
> Alternatively, you could try to update the version of
> smartmontools, although you probably don't have enough
> RAM or patience for it.
>
> > I shutdown, removed Knoppix live disk and booted to hdd with Ubuntu
> > 10.04, I then ran smartctl:
>
> > Device is: Not in smartctl database [for details use: -P showall]
>
> Use a new version of Ubuntu as live disk.
>
> I booted live Mint 14 and ran smartctl on new hdd. Did not want a project
> inside of a project.
mint at mint ~ $ sudo smartctl -a /dev/sda
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.0-17-generic] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST9750420AS
Serial Number: 6WS2VNV8
LU WWN Device Id: 5 000c50 05b0e28ed
Firmware Version: 0001SDM5
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Mon Feb 4 18:30:09 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 141) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 006 Pre-fail
Always - 70488
3 Spin_Up_Time 0x0003 098 098 085 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 14
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail
Always - 32
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 1
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 7
184 End-to-End_Error 0x0032 100 100 099 Old_age
Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age
Always - 0
188 Command_Timeout 0x0032 100 253 000 Old_age
Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x0022 064 060 045 Old_age
Always - 36 (Min/Max 26/36)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age
Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
Always - 0
193 Load_Cycle_Count 0x0032 100 100 000 Old_age
Always - 26
194 Temperature_Celsius 0x0022 036 040 000 Old_age
Always - 36 (0 26 0 0 0)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age
Always - 70488
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age
Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age
Offline - 118154550312961
241 Total_LBAs_Written 0x0000 100 253 000 Old_age
Offline - 0
242 Total_LBAs_Read 0x0000 100 253 000 Old_age
Offline - 10805
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
mint at mint ~ $
The above results came up instantly. Do not think it checked the entire
disk for bad sectors.
Will read man about -t and -T options to run longer tests.
Tom
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.colug.net/pipermail/colug-432/attachments/20130204/7251d097/attachment-0001.html
More information about the colug-432
mailing list